Schließen Zurück Alle Abschnitte einklappen
Prozess-Datensatz: AF/ArmaFlex Evo insulation for industrial and building installation (de) en

Tags Dieser Datensatz ist Bestandteil der ÖKOBAUDAT.
Kerninformationen des Datensatzes
Ort RER
Referenzjahr 2022
Name
AF/ArmaFlex Evo insulation for industrial and building installation
Anwendungshinweis für Datensatz Scope: Product line AF/ArmaFlex Evo Insulation material for industrial and building installations vulcanized in tubes and sheets. This declaration is an Environmental Product Declaration according to ISO 14025 describing the average environmental performance of the product produced in Germany, Spain and Poland. The average has been calculated based on site specific annual production volumes. As the installation of the product is not restricted to countries where the products have been produced the validity of this EPD is considered at least EU wide. System boundary: The data collection refers to the yearly production in 2020. The following life cycle stages are considered: Type of EPD: Cradle-to-Gate with options. Production A1-A3: The LCA calculation covers the production of the raw materials (supply chain – A1), the mixing of raw materials according to the respective recipes (MasterBatch) exclusively done in Münster, Germany, the transport (A2) of the MasterBatches to the production facility for foaming and the foaming process (A3) in Germany, Spain or Poland, including the packaging material. Transport A4: Average values for the transport from factory gate to construction site are assumed. Installation A5: The installation considers the production of off-cuts, incineration of these off-cuts and the disposal scenario for the packaging material. Auxiliaries like adhesives or tapes or energy for installation are not considered. End-of-life C2, C3: An incineration scenario for the used and demolished product, including an assumption for the transport to disposal, is covered. Benefits for the next product system D: Credits for electrical and thermal energy resulting from the waste incineration process of the off-cut material and packaging (A5) and the product (C3) are declared in module D.
Technisches Anwendungsgebiet AF/ArmaFlex Evo is used to insulate pipes, air ducts and vessels including fittings and flanges of industrial installations and building equipment. Condensation control, energy saving and noise control in refrigeration and air conditioning equipment and process plants. Energy saving according to local energy- saving laws, prevention of heat loss and noise reduction of heating and plumbing systems. Condensation control and noise reduction in service-water and waste-water systems. Condensation control, energy saving and noise control in refrigeration and air- conditioning equipment in the ship-building sector.
Gliederungsnummer 2.19.01
Klassifizierung
Klassenname : Hierarchieebene
  • OEKOBAU.DAT: 2.19.01 Dämmstoffe / Kautschuk / Schaum
  • IBUCategories: 02 Building products / Thermal insulation products / Insulating materials made of foam plastics
Allgemeine Anmerkungen zum Datensatz AF/ArmaFlex Evo is the professional, highly-flexible, closed-cell elastomeric foam insulation (FEF) for continuous energy saving and condensation control purposes. The combination of very low thermal conductivity and extremely high resistance to water vapour transmission prevents long-term energy losses and water vapour ingress and reduces the risk of corrosion under insulation.
Copyright Ja
Eigentümer des Datensatzes
Quantitative Referenz
Referenzfluss(flüsse)
Materialeigenschaften des Referenzflusses
    • Rohdichte: 52.5 kg/m^3
Zeitliche Repräsentativität
Datensatz gültig bis 2027
Technologische Repräsentativität
Technische Beschreibung inklusive der Hintergrundsysteme ArmaFlex Evo products are manufactured in a pressureless, continuous and discontinuous production process. In the first step, a homogenous compound is produced with rubber, additives, ancillary materials, blowing and vulcanization agents. This is done on the rolling mill or in the internal mixer followed by the rolling mill. Rubber extruders are used to process the compounds to produce raw profiles with defined dimensions. Here exact compliance with the dimensions for the raw profile is crucial for the dimensional accuracy of the foamed product. In the case of the discontinuous, pressureless production process, the raw profiles are cut to length and then foamed in a hot-air oven. In the case of the continuous, pressureless process, the extruded profile is fed directly onto a vulcanization line whose energy source may be hot air. In foam production, vulcanization and blowing processes run alongside each other. Both reactions are regulated by temperature control. Recipe and temperature control determine the properties of the foam. Quality assurance: EC Certificate of conformity no. 0543 of the Gütegemeinschaft Hartschaum e.V. Celle. Quality management system in accordance with EN ISO 9001. Declared unit: The declaration refers to 1 m³ insulation product. For the LCA calculations the average density per product brand is used. As additional information and support for installers the thermal conductivity coefficient (lambda-value) and R-value per 20 cm thickness per product brand are given.

Parameter zur Beschreibung des Ressourceneinsatzes und sonstige Umweltinformationen

IndikatorRichtungEinheit Herstellung
A1-A3
 Transport
A4
 Einbau
A5
 Transport
C2
 Abfallbehandlung
C3
 Recyclingpotential
D
Input
  • 1.58E+3
  • 2.82
  • 122
  • 0.185
  • 56.3
  • -146
Input
  • 104
  • 0
  • -104
  • 0
  • 0
  • 0
Input
  • 1.68E+3
  • 2.82
  • 18.2
  • 0.185
  • 56.3
  • -146
Input
  • 2764
  • 50.6
  • 51
  • 3.32
  • 1.15E+3
  • -649
Input
  • 905.5
  • 0
  • -7.51
  • 0
  • -898
  • 0
Input
  • 3.67E+3
  • 50.6
  • 43.5
  • 3.32
  • 252
  • -649
Input
  • 31.39
  • 0
  • 0.3139
  • 0
  • 0
  • 0
Input
  • 0
  • 0
  • 0
  • 0
  • 0
  • 0
Input
  • 0
  • 0
  • 0
  • 0
  • 0
  • 0
Input
  • 1.47
  • 0.00323
  • 0.0541
  • 0.000212
  • 0.274
  • -0.143
Output
  • 0.0000153
  • 2.55E-9
  • 1.55E-7
  • 1.68E-10
  • 4.5E-8
  • -1.46E-7
Output
  • 20.9
  • 0.00751
  • 1.19
  • 0.000494
  • 83.5
  • -0.304
Output
  • 0.0814
  • 0.0000612
  • 0.00108
  • 0.00000402
  • 0.00741
  • -0.0471
Output
  • 0
  • 0
  • 0
  • 0
  • 0
  • 0
Output
  • 0
  • 0
  • 4E+1
  • 0
  • 0
  • 0
Output
  • 0
  • 0
  • 0
  • 0
  • 0
  • 0
Output
  • 0
  • 0
  • 22
  • 0
  • 137
  • 0
Output
  • 0
  • 0
  • 39.5
  • 0
  • 2.5E+2
  • 0

IndikatorEinheit Herstellung
A1-A3
 Transport
A4
 Einbau
A5
 Transport
C2
 Abfallbehandlung
C3
 Recyclingpotential
D
  • 1.4E+2
  • 3.82
  • 80.5
  • 0.251
  • 136
  • -37.6
  • -75.1
  • -0.00484
  • 76.3
  • -0.000318
  • 0.0275
  • -0.187
  • 214
  • 3.79
  • 4.23
  • 0.249
  • 136
  • -37.4
  • 0.298
  • 0.0311
  • 0.00378
  • 0.00204
  • 0.0305
  • -0.0258
  • 8.55E-10
  • 4.85E-16
  • 8.64E-12
  • 3.19E-17
  • 2.18E-13
  • -4.26E-13
  • 0.623
  • 0.00993
  • 0.00864
  • 0.000653
  • 0.0358
  • -0.039
  • 0.682
  • 0.0111
  • 0.00949
  • 0.000727
  • 0.0369
  • -0.0488
  • 1.48
  • 0.0563
  • 0.0271
  • 0.0037
  • 0.152
  • -0.149
  • 0.0026
  • 0.0000113
  • 0.000027
  • 7.4E-7
  • 0.0000336
  • -0.0000487
  • 0.159
  • 0.00503
  • 0.00248
  • 0.000331
  • 0.0123
  • -0.0139
  • 22.4
  • 0.0329
  • 1.88
  • 0.00217
  • 10.5
  • -2.86
  • 3.67E+3
  • 50.5
  • 43.4
  • 3.32
  • 252
  • -649
  • 0.471
  • 2.89E-7
  • 0.00476
  • 1.9E-8
  • 0.00000311
  • -0.00000621

IndikatorEinheit Herstellung
A1-A3
 Transport
A4
 Einbau
A5
 Transport
C2
 Abfallbehandlung
C3
 Recyclingpotential
D
1Diese Wirkungskategorie behandelt hauptsächlich die mögliche Wirkung einer ionisierenden Strahlung geringer Dosis auf die menschliche Gesundheit im Kernbrennstoffkreislauf. Sie berücksichtigt weder Auswirkungen, die auf mögliche nukleare Unfälle und berufsbedingte Exposition zurückzuführen sind, noch auf die Entsorgung radioaktiver Abfälle in unterirdischen Anlagen. Die potenzielle vom Boden, von Radon und von einigen Baustoffen ausgehende ionisierende Strahlung wird ebenfalls nicht von diesem Indikator gemessen.
2Die Ergebnisse dieses Umweltwirkungsindikators müssen mit Bedacht angewendet werden, da die Unsicherheiten bei diesen Ergebnissen hoch sind oder da es mit dem Indikator nur begrenzte Erfahrungen gibt.
Comparative toxic unit for humans (carcinogenic) (HTP-c) 2
  • 6.77E-8
  • 7.36E-10
  • 8.72E-10
  • 4.84E-11
  • 8.29E-9
  • -6.18E-9
Comparative toxic unit for humans (noncarcinogenic) (HTP-nc) 2
  • 0.00000573
  • 4.29E-8
  • 7.11E-8
  • 2.82E-9
  • 8.79E-7
  • -2.44E-7
Incidence of disease due to PM emissions (PM) 2
  • 0.0000321
  • 6.16E-8
  • 3.45E-7
  • 4.05E-9
  • 9.37E-7
  • -4.2E-7
Human exposure efficiency relative to U235 (IR) 1
  • 8.33
  • 0.00876
  • 0.121
  • 0.000576
  • 0.771
  • -7.72
Comparative toxic unit for ecosystems (ETP-fw) 2
  • 3.55E+3
  • 36.5
  • 39.8
  • 2.4
  • 206
  • -136
Soil quality index (SQP) 2
  • 5.47E+3
  • 17.3
  • 56.9
  • 1.14
  • 55.4
  • -1E+2